@justinordonez75
Profile
Registered: 2 years, 5 months ago
Guide to Selecting the Proper Hairdressing Scissors
Step 1 - The deal with
You will have seen earlier than the basic scissor deal with design. It is straight, it's even length, but it's not designed for people.
You will additionally probably have seen the offset handle. With this scissor handle, one of many finger rings is shorter in length than the other. This is widely recognised because the superior type of hairdressing scissor and you can see why if you are able to hold both together.
You'd see that whilst the straight scissor is at 12 o'clock, the offset scissor is at 1 o'clock. This implies that if you're working - in case you're point slicing with a straight deal with scissor for instance, your elbow and your wrist are very high, which is quite uncomfortable and never a good posture. Whereas with the offset, it is far lower.
Once you're cutting against skin, the straight handle is quite obstructed and I will typically see stylists lifting the scissor off as they cut across the skin. Nonetheless, with the offset handle there's little or no obstruction in slicing against the skin.
If you want to taper to its only, you can choose the offset Rotating Thumb Scissor, or what we call the Revo, Revolving Thumb scissor.
For those who were to put it alongside any straight deal with scissor, you'll again see that the straight handle scissor is open whereas the offset is closed. This is because the hole between your finger and thumb is larger, which puts less pressure on the carpel tunnel nerve.
Secondly you'll notice the angle which you know makes the elbow lower. Third and most importantly, when you're working on any haircut, slicing over the knuckles, it lets you drop your elbow, to a much more relaxed and comfortable position, which goes to save plenty of aches and pains.
Step 2 - The Blade
There are really only types of scissor blades. The primary are mainly made in Europe, often Germany, they are flat, the blades are straight, they have a beveled, virtually kind of a chiseled edge, they usually typically have serrations. These lower like a guillotine. When the hair hits the blade, it cannot move and off it comes. They don't slice cut, they only cut still.
Convex blades are very different. This has received a curve on the blade, it is hole ground, it's made from pieces of metal, and instead of the European scissors which is made in at some point, this takes up to weeks to make. The distinction is with this you possibly can slice cut as well as minimize crisp, straight lines. These are acknowledged as a much superior type of blade.
Step 3 - The Type of Scissor
I'd always suggest choosing a Long Blade, a Short Blade, a Thinning Scissor, and a Layering / Texturiser scissor. With these 4 key "Instruments of the Trade" you'll be able to take on any haircut in probably the most environment friendly way.
A lot of hairdresser will start their careers with the Quick Blade scissor, round 5" in length. But lots will end their career with it too, by no means understanding the difference between blade lengths.
If you can only use a short blade, bear in mind it's designed to be used, initially, for slicing hair inside the fingers in the palm of the hand, and for reducing towards the skin in very small, precise sections. That is OK should you do that kind of work.
However in the event you use a way the place you create texture type haircuts, or if your reduce over the knuckles, the longer blade means that you may reduce there much more easily. In case you level minimize, the blade's long sufficient to go into sections.
A number of hairdressers use a short blade to chop over the knuckles. The problem is the blade is just not as stable, and you'll usually see them go in one, , three, and minimize the skin. Or if they point minimize, they're going to move the scissor hand and actually lower off an excessive amount of hair on the way in.
So remember, in case you do cut over the knuckles, a Longer Blade (6" - 6.5" in size) is going to give you a cleaner line a lot more safely, and if you happen to level reduce, a much softer haircut without having to move your scissor hand.
I additionally suggest that every stylist use a 30 Tooth Thinning Scissor. How many occasions does a hairdresser must remove weight from the hair without seeing any cut marks? What number of occasions do they need to mix two sections collectively? This is designed to get the proper completed outcome when you're blending together. A few of my purchasers really describe it as "evaporating" the hair away with no marks.
One other important piece of equipment is the 15 Tooth Layering / Texturising Scissor. This has primary jobs; one is to create soft layers, and the other is to create texture.
The question is: what number of instances do you do a haircut that you want to create soft texture?
Most stylists, the ones that haven't been educated in regards to the 15 Tooth, will use a strong blade scissor, do the entire haircut, blow-dry it, and then go over and point minimize with the strong blade. In order that's two hair cuts on one client.
Through the use of the 15 Tooth Layering / Texturising Scissor, you will get that lead to one go. It may be accomplished over your fingers, over your knuckles, or scissor over comb. This is probably one of the crucial underused, but groundbreaking products available on the planet of hairdressing today.
For more info on Japanese steel hairdressing scissors stop by our own site.
Website: https://www.jpscissors.com/blogs/hair-scissors/top-10-best-hair-cutting-scissors
Forums
Topics Started: 0
Replies Created: 0
Forum Role: Participant